Honda Foreman Forums banner

Dang

3112 Views 5 Replies 4 Participants Last post by  trail_shredder_crf
Well I put a clutch kit in my foreman and when I took the es motor off I noticed the some of the splies were missing on the end of the shift rod. So I put it back togather and now most of them are gone and it wont shift at all.Anyone have any idea on how much a new shift rod and spline would be to fix?
1 - 6 of 6 Posts
This info is from <a href="http://www.hondaparts-direct.com/default.asp" target="_blank">http://www.hondaparts-direct.com/default.asp</a>
Prices will be higher at a dealer

01 COVER, FR. CRANKCASE 11330-HN0-770 001 $97.12
02 COVER, OIL FILTER 11333-HC4-000 001 $32.92
03 O-RING 11336-HN0-A10 001 $4.02
04 PROTR, ANGLE SENSOR 11339-HN0-770 001 $6.22
05 GASKET, FR. 11394-HM7-003 001 $11.92
06 VALVE, RELIEF 15231-HM3-670 001 $5.74
07 SPRING, RELIEF VALVE 15232-HM3-670 001 $0.86
08 CAP, RELIEF VALVE 15235-HM3-670 001 $10.00
09 ELEMENT, OIL FILTER 15412-HM5-A10 001 $3.92
10 RUBBER, FILTER 15413-MC8-000 001 $1.74
11 SPRING 15414-KF0-000 001 $2.15
12 LEVER, CLUTCH 22810-HM7-700 001 $38.66
13 PLATE, CLUTCH CAM 22820-HM7-010 001 $18.34
14 SPRING 22825-HN0-671 001 $1.91
15 PLATE, CLUTCH LIFTER 22830-HC4-000 001 $10.36
16 BOLT, CLUTCH ADJ. 22841-HC4-000 001 $3.81
17 RETAINER, BALL 22860-HB3-000 001 $3.93
18 GEAR (40T/12T) 24616-HN0-771 001 $9.25
19 GEAR (41T/10T) 24615-HN0-771 001 $8.42
20 GEAR, REDUCTION (7T) 24617-HN0-771 001 $4.28
21 MOTOR ASSY., CONTROL 31300-HN0-A12 001 $119.20
22 SENSOR ASSY., ANGLE 38800-HN5-A11 001 $42.80
23 BOLT, SOCKET (5MM) 90116-KCY-671 002 $2.74
24 WASHER (10X21.5) 90413-GE0-000 001 $2.02
25 BEARING (6303SP) 91009-HA0-004 001 $18.05
26 BEARING (696ZZ) 91050-HN0-A11 001 $5.17
27 BEARING (626ZZ) 91060-HN0-A11 003 $5.32
28 BEARING (698ZZ) 91070-HN0-A11 001 $5.42
29 OILSEAL(10X20X5)91202-HC0-003(replaces 91201-KM1-005)001$2.07
29 OIL SEAL (10X20X5) 91202-HC0-003 001 $2.07
30 O-RING (54X2.4) 91302-KF0-003 001 $2.03
31 O-RING (11X1.9) 91303-HA0-004 001 $0.80
32 O-RING, ANGLE SENSOR 91308-HN0-A10 001 $1.27
33 O-RING (8.2X1.5) 91308-MC7-000 001 $0.71
34 NUT, HEX. (8MM) 94030-08000 001 $0.34
35 WASHER, PLAIN (5MM) 94101-05800 002 $0.31
36 WASHER, PLAIN (8MM) 94102-08800 001 $0.31
37 PIN, DOWEL (8X10) 94301-08100 001 $0.75
38 PIN, DOWEL (8X14) 94301-08140 002 $0.75
39 BOLT, FLANGE (6X35) 95701-06035-00 003 $0.55
40 BOLT, FLANGE (6X55) 95701-06055-00 010 $0.72
41 BOLT, FLANGE (6X85) 95701-06085-00 002 $0.88
42 BOLT, FLANGE (6X100)95701-06100-00 001 $1.06
42 NUT, FLANGE 95780-06500-00 (replaces 95701-06100-00) 001 $0.68
43 BOLT, FLANGE (6X18) 96001-06018-00 003 $0.63
44 BOLT, FLANGE (6X45) 96001-06045-00 001 $0.89
See less See more
Do you mean the splines are gone off the gearshift spindle .. Are these the splines that the (1/2 moon shaped) reduction gear runs on..?
Yea they are.
The gearshift spindle is fairly easy to change , but the rear engine cover must be removed so either the swingarm has to be removed or the engine must be pulled ...
1 - 6 of 6 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top