How do you reset the Computer - Honda Foreman Forums : Rubicon, Rincon, Rancher and Recon Forum
Reply
 
LinkBack Thread Tools
post #1 of 12 (permalink) Old 07-17-2008, 05:26 PM Thread Starter
Honda Addict
 
Join Date: Apr 2008
Location: Atoka, Tennessee
Posts: 175
How do you reset the Computer

on a 07 Rubicon..............?????

07 Camo Rincon
WWW.Tcountymuddawgs.com
Pappy1 is offline  
Sponsored Links
Advertisement
 
post #2 of 12 (permalink) Old 07-17-2008, 05:55 PM
Administrator
 
toodeep's Avatar
 
Join Date: Aug 2007
Location: south dakota
Posts: 11,220
Garage
turning the ignition switch off will reset the computer for temp. codes. to initialize the computer have the switch off, trany in neutral, and mode select switch in D1 or D2. hold both the up and down shift buttons and turn the switch on. then release and press up - down - up , move the throttle lever from fully closed to fully open and then back to fully closed. this all has to be done pretty fast and should here the control motor cycle.



2007 420FM (475cc, 27x12x12 Mudbugs) ---------- 1995 300FW (webcamshaft, 350 rear end)
2008 420FE (26x9x12 BearClaws) -------------------
1988 300 (old stock machine, nothing fancy)
2009 420FA (25x8/10x12 BearClaw HTR) ---------
1987 350D (work in progress)

toodeep is online now  
post #3 of 12 (permalink) Old 07-17-2008, 10:44 PM Thread Starter
Honda Addict
 
Join Date: Apr 2008
Location: Atoka, Tennessee
Posts: 175
Sounds easy enough......thanks for the info...

07 Camo Rincon
WWW.Tcountymuddawgs.com
Pappy1 is offline  
post #4 of 12 (permalink) Old 07-18-2008, 09:08 AM
Honda Rider
 
Join Date: Dec 2007
Location: morinville alberta
Posts: 77
you forgot to ad this one very important step. if you dont do it, it wont work. hold your tongue to the left and mutter swears under your breath. i have had some success with the right side but left never fails. lol.

MEH!
PLUMBUM is offline  
post #5 of 12 (permalink) Old 07-18-2008, 03:35 PM Thread Starter
Honda Addict
 
Join Date: Apr 2008
Location: Atoka, Tennessee
Posts: 175
QUOTE ("PLUMBUM":35mhqmb2)
Quote:
you forgot to ad this one very important step. if you dont do it, it wont work. hold your tongue to the left and mutter swears under your breath. i have had some success with the right side but left never fails. lol.
Yea I will do and your right the left side always works best......sometimes the middle....but very rare

07 Camo Rincon
WWW.Tcountymuddawgs.com
Pappy1 is offline  
post #6 of 12 (permalink) Old 08-15-2013, 08:09 PM
Honda Rider
 
Join Date: Aug 2013
Posts: 15
okay i just reset mine heard some winding ond stuff but it did not fix the promblem
ccdatvs is offline  
post #7 of 12 (permalink) Old 08-15-2013, 09:06 PM
Honda Red Wing Rider
 
martdog420's Avatar
 
Join Date: Aug 2009
Location: ontario canada
Posts: 1,832
Quote:
Originally Posted by ccdatvs View Post
okay i just reset mine heard some winding ond stuff but it did not fix the promblem
What is the problem with the machine??

2006 Rubicon Canadian Trail Edition.
1 1/2 inch Quadrax lift
26" Mudlites
Motovan B series back seat
2500# warn
1000's of custom scratches
100's of dings n dents
50+ plastic stitches
and a few oil changes.
martdog420 is offline  
post #8 of 12 (permalink) Old 08-15-2013, 11:00 PM
Honda Rider
 
Join Date: Aug 2013
Posts: 15
alright here we go my machine runs great but is stuck in gear gives a blank code-- on the gear idicator i checked the cdi wires for loose/bad connections with no luck i pulled the electric motor on the side of bike that the electric shift switch is on the handel bars when i hooked the battery to it the motor tuned freely back and forth i then pulled the angel sensor cheked the wires from it to the cdi box they were good with no shorts tested with a multimeter put the motor back on it and with a 12volt battery i shifted if fine so what do i do now it goes in gear just dosent shift at all on its on
ccdatvs is offline  
post #9 of 12 (permalink) Old 08-15-2013, 11:08 PM
Honda Red Wing Rider
 
rich450es's Avatar
 
Join Date: Nov 2010
Location: tooele, utah
Posts: 17,263
my guess (and it is a guess) is to get the oil preasure tested .......wate for toodeep to come on

2000 foreman 450 es-s
the f**king pig
SOLD!
Hondaforeman.com stickers for sale .....pm me for details !
friend me on facebook
https://www.facebook.com/richard.chayer.5
i love (.)(.)s
rich450es is online now  
post #10 of 12 (permalink) Old 08-15-2013, 11:24 PM
Administrator
 
toodeep's Avatar
 
Join Date: Aug 2007
Location: south dakota
Posts: 11,220
Garage
We have been chatting about this already. Did you remove the angle sensor? If so did you get it pre loaded when installing it again? I've been trying to find something on that "out of place" connector but I will have to look through the manual tomorrow when I get to work (PDF is taking too long to navigate around).



2007 420FM (475cc, 27x12x12 Mudbugs) ---------- 1995 300FW (webcamshaft, 350 rear end)
2008 420FE (26x9x12 BearClaws) -------------------
1988 300 (old stock machine, nothing fancy)
2009 420FA (25x8/10x12 BearClaw HTR) ---------
1987 350D (work in progress)

toodeep is online now  
Sponsored Links
Advertisement
 
Reply

Quick Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome